Concrete Sealer Remover

by scott paul

failed concrete sealerConcrete Sealer Remover Tips

How to tips for removing a failed Concrete Sealer that has discolored or turned white.

Sealing concrete is a great way to increase appearance and longevity. Driveways, sidewalks, patios, porches, brick pavers, and stonewalls can be sealed to enhance their look and block out moisture.

There are several types of concrete sealers that have different finishes. From matte finishes to the high gloss “wet look” type sealers. In the case where a concrete sealer fails it may be necessary to remove it before resealing with a new concrete sealer.

There are several reasons a concrete sealer can fail. Over application can cause the sealer to fail prematurely. Cheap or inferior sealers just do not last or hold up well. Moisture can also penetrate a sealer and cause it to fail. Some sealers will turn yellow or white when they fail and can be very unsightly.

 

To remove an old failing concrete sealer you have to use a concrete sealer stripper that is tough enough for the job. RADStrip Concrete and Paver Sealer Stripper is a powerful stripping chemical that will remove most acrylic concrete and paver sealers.

SuperSeal Concrete Sealer Remover is easy to use yet extremely effective. Application of the product is as follows:

1. Roll the SuperSeal Concrete Sealer Remover on the failed sealer in sections of 10×10.

2. Allow SuperSeal Stripper to sit on failed sealer for 10-20 minutes.

3. Power wash the surface and reapply if needed.

4. Apply to next section and repeat until completed. For stubborn areas, reapply and let dwell longer.

SuperSeal Concrete Sealer Remover covers approximately 75-150 square feet per gallon depending on existing sealer. Always follow the application instructions on the label and wear personal protection equipment like safety glasses and chemical resistant gloves.

Once you are sure that you have removed all the old failing concrete sealer, rinse the surface well and allow it to dry for several days before applying a new sealer.

Protecting your concrete surfaces is a good investment. It improves the appearance and longevity of the concrete. Removing all the old sealer prior to applying new can make a huge difference in the performance of the new concrete sealer.

 

If you have any questions on removing a failed sealer, please ask below

Subscribe
Notify of
guest
18 Comments
Newest
Oldest
Inline Feedbacks
View all comments
Frances
Frances
9 months ago

Can you use the super seal stripper to remove sealer from outside granite tiles?  They are about 24×24 in size 

beading_water_concrete_smal
Admin
9 months ago
Reply to  Frances

What type of sealer are you removing?

Frances
Frances
9 months ago
Reply to 

it was alliance gator seal.  

beading_water_concrete_smal
Admin
Frances
Frances
9 months ago
Reply to 

OK.  this is what the sealer looks like on the granite

beading_water_concrete_smal
Admin
9 months ago
Reply to  Frances

it will remove it but make sure you cover the paint on the house and railings as well.

Freddy Perez
Freddy Perez
1 year ago

Good day, I’ve been given the job to clean this, I tried pressure washing and soft washing, with no rests. apperantly there is some kind of sealer. I’ve attached pictures, can you advise of what would be best 

David parker
David parker
3 years ago

Does the super seal stripper damage or kill plants and grass.

beading_water_concrete_smal
Admin
3 years ago
Reply to  David parker

You should cover and rinse well when done all plants and grass to avoid any damage. Direct contact can “burn” the plants leaves and grass.

Toni
Toni
4 years ago

Several days after removing failed sealer from a portion of the brick facing on our house that portion still looks darker than the rest of the wall, like it’s wet. How do we even out the color?

beading_water_concrete_smal
Admin
4 years ago
Reply to  Toni

Post a picture.

Oswaldo valdez
Oswaldo valdez
5 years ago

How can I remove these sealer Stains? What product can you recommend me to remove those white sealer stains

beading_water_concrete_smal
Admin
5 years ago
Reply to  Oswaldo valdez

Without knowing what the sealer brand or type was used before, it is very hard to answer this correctly. Do you have more info for us?

Oswaldo valdez
Oswaldo valdez
5 years ago
Reply to 

This is the sealer I put on my concrete

beading_water_concrete_smal
Admin
5 years ago
Reply to  Oswaldo valdez

This and high pressure washing should remove it: https://www.concretesealerstore.com/concrete-sealer-remover.html

beading_water_concrete_smal
Admin
9 years ago

It will not harm the concrete but it is possible to remove some of the “release” color that is added on top of the concrete when installed. No way around this.

Katie
Katie
9 years ago

Can you comment if the SuperSeal Concrete Remover is safe for colored cement. My patio is a dark red/maroon with some gray in it.
Thanks!

18
0
Would love your thoughts, please comment.x