·
05/12/2016
No need to add tint. Look at the SS30 if you want a higher gloss or SuperSeal Matte for a lower shine.
SuperSeal30 can be used for Stamped Concrete, Stamped Cement, Decorative Cement, Bricks, Acid Stained Cement, Concrete Stains, and Exposed Aggregate. SuperSeal enhances the natural color of your Concrete Brick Pavers and Cement with a "wet" look.
SuperSeal30 can be applied with a 1/2" roller cover. You cannot use a sprayer.
SuperSeal30 will help sand erosion reducing the amount of weeds.
One coat is recommended. Coverage is about 100 feet per gallon or 500 feet per five gallon.
One coat will result in a high gloss sheen depending on porosity of brick. Extra coats will result in a higher gloss.
This Product is not VOC Compliant in Every State
Click here for a VOC Compliant Product
Super Seal 30 is not suggested for Clay Pavers.
Related Products
You are guest ( Sign Up ? )
or post as a guest
Loading comment...
The comment will be refreshed after 00:00.
-
We will reply to your comment shortly
-
We will reply to your comment shortlyI have a colored concrete pool deck that needs re-sealing (powdered dye was mixed into the concrete). The color is faded but looks good wet - I prefer a 'wet look' finish anyway. In Missouri, what SS product do you recommend and should is an added tint available/necessary to restore the color? Thanks, Jim.
-
We will reply to your comment shortlyYou can use a product called Shark Grip. Mix thoroughly before applying.
-
We will reply to your comment shortlyIVE USED THIS PRODUCT TWICE BEFORE AND IT IS AWESOME!!! THIS TIME I WAS CONSIDERING ADDING SAND/GRIP SO IT ISNT SLIPPERY. I WAS GOING TO BUY IT FROM THE PAINT STORE OR EVEN HOME DEPOT. WILL IT RUIN THE SUPER SEAL 30 WET LOOK OR ITS APPEARANCE IN ANY WAY? THANKS
-
We will reply to your comment shortlyThe stripper we sell is for outside use only. Not sure if any stripper will work indoors as they all need a pressure washer to work with. Too much mess and fumes when trying to do inside. Might be best to have it grinded off.
-
We will reply to your comment shortlyWhat do I use to strip super seal 30 off of a concrete floor in a veterinarian clinic?
-
We will reply to your comment shortlyUsually a couple of days but depends on the weather outside. Not sure why it would get in the house though.
-
We will reply to your comment shortlyHow long does it take for the odor to dissipate? I used super seal 30 on my lanai brick pavers. My entire house still has a strong odor from the super seal30.
-
We will reply to your comment shortlyAs long as you are 100% sure that you did leave any polymeric sand dust on top of the pavers then you can seal when dry. Failure to remove the poly sand dust prior to wetting with water can result what is known as "poly haze" and is known issue with many polymeric sands.
-
We will reply to your comment shortlyI had brick pavers installed 1 year ago. Never sealed. I put polmeric sand in the joints and blew off excess. I wetted the joints lightly 3 times to harden the sand which it did. How long do I have to wait to apply the sealer.
-
We will reply to your comment shortly24-48 hours for vehicle traffic.
-
We will reply to your comment shortlyOne question: I coated my aggregate driveway yesterday.(10/10/15) How many days do you suggest I wait until I begin driving on the newly sealed driver.
-
We will reply to your comment shortlyCarl, Next day should work.
-
We will reply to your comment shortlyHow long must I wait to coat with SuperSeal 30 after repairing with exposed aggregate crack filler?
Thanks -
We will reply to your comment shortlyTypically not slippery after full cure of about 2 weeks.
-
We will reply to your comment shortlyregarding the superseal30 product.... is it slippery after application? i am considering applying it to a concrete aggregate driveway as well as brick front stoop and brick covered patio. thank you!
-
We will reply to your comment shortlyYou most likely have to strip off the Valspar sealer for the SS30 to work properly.
-
We will reply to your comment shortlyI installed a 72'x 3.5' sidewalk with Allen & Roth concrete pavers. Brushed concrete sand mixture between pavers which turned pavers white. Pressure washed and used muriatic acid to remove concrete residue. Then sealed with Valspar waterbased sealer for "wet look" and to bring the color out. NOT. My question. Because the pavers have been etched with muriatic acid and sealed. Will Superseal 30 give me the "wet look" and bring out the color? Will I get the just rained on look?
-
We will reply to your comment shortlyTry applying Xylene to the affected areas.
-
We will reply to your comment shortlylove the product.....i sealed stamped concrete .pressure washed first ..let dry in good hot sunny days. 3 days later we sealed our walkway. looked great for 2 weeks then a few white/dry ? ?patches showed up . the rest of the sealed walk looks great .any idea helpfull.
-
We will reply to your comment shortly
-
We will reply to your comment shortly
-
We will reply to your comment shortlyCAN I USE SUPER SEAL 30 IF I USE CIPA DECK AND PAVER SEALER LAST YEAR
-
We will reply to your comment shortlyIt depends on the brand and type of water based sealer that is was. Definitely no if the old sealer has discolored or blushed by turning white.
-
We will reply to your comment shortly
-
We will reply to your comment shortlyYou probably over applied and now you maybe be trapping in moisture. Does it look milky?
-
We will reply to your comment shortly6 month old concrete patio acid stained sealed with ss30. I have 3 coats of sealer on. Some areas r shiny and others not so much. Some places look dirty like I need to sweep after it rained-had been down 2 weeks prior to rain and didn't look like this until after rain. I washed patio with soap and water, with stiff broom and sprayed off. Why do u suppose it looks like it's dirty and how many coats of sealer do I need? One store told me as many coats as it takes to make it shiny and another said no more than 2 coats.
-
We will reply to your comment shortlyAl, use this to fill the cracks:
http://www.concretesealerstore.com/Exposed-Aggregate-Crack-Filler.html
Not sure on the white spots as the SS30 does not cover. If you cannot see the white spots when wet with water then most likely you will not see the spots when the SS30 is applied. -
We will reply to your comment shortly
-
We will reply to your comment shortlyAs long as the Behr has not discolored by turning white then you should be okay.
